Tuesday, June 30, 2009

How to Build a Chicken Plucker

Back in the game! I apologize for the break but I just could not keep up with everything. The pig roast went well and I will share pictures soon. I never did catch up on reading other blogs but hope to in the near future. The following post is written by Maine Man.
I'll start by saying thank you to Angie & Eric over at Children in the Corn for giving us plans to build this project! I had been looking at the whiz-bang chicken plucker on the Internet for a couple of years but I probably would not have carried through without the plans.
The plucker fingers came from Kent Company which is based out of Florida. They were very helpful and friendly folks. These silly little pieces of rubber were one of the most expensive items in the project costing approximately $120 with shipping. Most of the other parts I had with exception to the lumber, screws, and coupling.
Prior to installing 120 plucker fingers you should first drop a brick on your toe while listening to some very loud aggressive music. Anger will make these buggers go in a bit easier. Beveling the outside of the 3/4 inch hole and standing inside the barrel while pulling inward is also a big help. Some liquid encouragement may be needed for this portion of the project. Take note of the redness and veins in my forehead.

I lag screwed the frame together and sealed all the wood with some leftover stain I had kicking around the shed. When I first saw this contraption I thought the tub spun like a washing machine but that is not the case, it is just there to contain the birds.


This is the feather plate, the part that performs the actual plucking process. The plan called for a 1/4 inch plate of aluminum which was rather costly to purchase. Instead I opted to build it from the bottom portion of the barrel and 3/4 inch plywood. I attached them together with #14 self taping screws. It made a rock solid inexpensive plate.


Rather than use a belt and pulley system as the plan calls for I used the auger blade gearbox from an old snow blower that was in the barn. It was a 10:1 ratio which worked perfect with an electric motor that turns 1725 rpm and giving me a speed of around 175 rpm on my feather plate. The bearing block you see on the picture above is an idler wheel off a snowmobile suspension. I installed a jack shaft bearing, the type with a locking ring. That part was from a snowmobile as well. You know you live in Maine when half of your Yankee ingenuity involves some sort of snow related items. Despite this confabulation of parts its construction is far stronger that it needs to be and I am certain it will last for years, perhaps a lifetime.




This is a love joy coupling. It worked great for attaching the electric motor to the transmission. On the first try I weld up a rigid coupling. I had alignment issues which caused quite a bit of vibration. The love joy has a rubber connector in the middle which is tolerant of misalignment and only cost $22.
I had a 1/3 hp motor in the shed off an old bench grinder. Once again I deviated from the plans which called for a 3/4 hp. I knew as soon as I spent $200 on a new one a free-be would appear. As luck would have it my father-in-law was given one by his neighbor. I've yet to install it but must say the 1/3 hp did an excellent job on the average size birds and also worked on the 10lb birds but would bind up on occasions.


The one thing I need to add is a splash guard around the feather plate outlet to keep the chicken soup off your legs and out of your boots. Spraying the bird with the garden hose as it is being plucked keeps the fingers free of feathers and speeds up the process. The process is so amazing, you never realize your boots are filling with chicken juice until you turn off the plucker.

On the left side there is a plastic tote that I modified to keep the electric motor clean and dry.





Looks like fun, who's next?




The finished product 30 seconds later. Bald is beautiful, especially when it comes to chickens. This one dislocated a wing shortly after it became separated from its head. This has been an ongoing problem for me. I have found completely restraining the bird helps keep the muscle spasms from breaking wings but it's not always 100% effective in treating separation anxiety. I've yet to try the killing cone method. Perhaps on the next batch of birds I will.



You must have a thermometer or the whiz bang plucker will make a mess of your birds very quickly. The picture below clearly shows what guess work will get you, boneless chicken every time.
Scald your birds for approximately 30 seconds @ 13o degrees. You'll notice the color of the shin which is normally a yellowish white color will develop a tanish appearance at which point is prime for plucking.



Oops, too hot! Better get out the knife and start boning.




I caught, killed, and plucked seventeen 8-10lb birds in just 40 minutes by myself, not too shabby. It cost about $200 to build. Without my extreme frugalness it would have cost closer to $400. That still is not bad considering similar factory built models start around $1200. I figure we will save a bundle in the long run. Our local butcher charges $3/chicken, $5/turkey and $7 or more for ducks and geese. Plus you have to make an appointment 3 weeks in advance. (don't I hate those long term commitments) Heaven forbid life goes astray and you have to reschedule. That will put you have 3 more weeks.....200 lbs of grain later.
By summers end we will have raised approximately 24 ducks, 80 chickens, and 5 turkeys for the freezer. This means it has more than paid for itself in the first year of use. More importantly than the money it has given us easy access to high quality food and a greater feeling on Independence which is priceless!


92 comments:

Lynnie said...

Fascinating! And excellent pics! I appreciate you showing us what happens if the water temperature is off, and all those other fine details! My husband processes all our birds using the same chicken plucker his grandpa used.

Throwback at Trapper Creek said...

Great post - I am almost tempted...when my friend moves to Montana and takes his chicken equipment we'll need one these.

Thanks MM for such a detailed and humorous tutorial!

sugarcreekstuff said...

What a great post Maine Man.
Wondering if you could send the plans my way? I think my hubby needs a project.

Lisa said...

I always wanted to know how the chicken pluckers work. We are considering raising meat birds next spring so this is all very helpful!

Anonymous said...

Excellent and entertaining post MM, you crack me up!! :) You are very welcome and I'm so glad it worked so well for you....but I had no doubt...yankee men rule!! :)

Anonymous said...

Pretty cool post, and pretty darn good piece of work, building the feather plucker!

Captain Hook and Lady Crochet said...

I missed ya! Welcome back! Hey... you wouldn't have copies of the plans you would sell or give away do ya? We have been wanting to make one as well...but like you, i am extremely frugal...and broke.LOL
Thanks.
Lori
PS: Feel free to email me!
stonebridgeapiary@yahoo.com

Vintage West said...

What a great and informative posting, Thanks for sharing!

Country Girl said...

THANKS FOR ALL YOUR RESPONSES. THE PLANS ARE ACTUALLY A BOOK. NOT SURE WHAT MAINE MAN PLANS TO DO WITH, I WILL ASK. I WILL ALSO POST THE NAME FOR ANYONE THAT IS INTERESTED.

country girl said...

The killing cone works very well; it restrains the chicken so no broken bones.

Lynnie said...

Just wanted to say my husband really enjoyed this post! His grandpa's plucker is apparently giving out so I showed him yours. He didn't know there were others out there doing this kind of thing and writing about it (what can I say, he's not an internet-boy, yet!). It all made a lot more sense to him than it did to me (love joy? I just thought you were getting all soft and fuzzy on us!) so maybe we'll have a nice new plucker sitting in our backyard soon! Thanks again!

Anonymous said...

Nice plucker, I was wondering if anybody has seen one that you attach to a bench grinder, just a smaller scale version of a rubber tipped pluckin deal, I'm raising a couple of turkeys and a few chickens and cannot justify building a whiz bang. THANKS RYAN

Jenny said...

We're (my husband, that is) in the process of building one of these now. I'm going to bookmark your post to show it to him. It directly addressed a couple questions he asked me to try to look up. Thanks for sharing!
~Jenny~

Dave Morgan said...

Thanks for the show..We are building a home now and will start raising birds next spring, I am looking for more info all the time.

Anonymous said...

hi
great job, but could you tell me were I can get the "rubber fingers"

Scroll Man said...

This is perfect. I am planning on building one of these but I have a few question how do I get in contact with you.
Thanks,
Dave

Country Girl said...

to contact us by e-mail send to achornfarmer@yahoo.com

Anonymous said...

I JUST READ YOUR COMMENTARY ON THE PLUCKER, IT IS QUITE GOOD,BUT YOU DO NOT NEED TO BUILD A SPLASH GUARD TO STOP THE CHICKEN SOUP FROM ESCAPING.
ALL YO HAVE TO DO IS LOWER THE TUB ABOUT THREE INCHES PAST THE FEATHER PLATE AND THIS WILL SOLVE THAT PROBLEM.

richelle6 said...

Has anyone ever heard of using the ends of the black bungee cords instead of buying the rubber fingers? Would they work?

Anonymous said...

here's a cheap one you could make for probably less than $10.00

http://www.backyardchickens.com/forum/uploads/30014_100_2721.jpg

Anonymous said...

Unreal!! I have been looking to make one of these, I havn't been able to find detailed pics like you have shown. Great job. Im going to try and make a smaller version of it though, to see how it will go with Quails.

Anonymous said...

hey the plucker is very nice and well worth the money it cost to build it .....can you tell me were i can buy the rubber fingers.....
thanks

Anna @ Blue Dirt said...

Some sort of cone WILL help you with your dislocating problems. My husband uses old jugs with holes cut out of them screwed onto a tree. There are lots of free options, another nice one I saw were actually traffic cones with an inch or so cut off the top and they made a frame that would hold 3 or 4 of them inverted.

Bent Nails said...

I'm in the process of making one of these. I've left the barrel in tact and drill 1 hole and fill it at a time. I spray the finger with PAM. I've been pressing the fingers in with a 2-lb. hammer. The trick is not to hit the finger really hard or everything bounces. About 3 licks per finger seem to work. I just don't like aggressive music. Gettin old. Anyway, thanks for a great site, it's really helpful.

Vegetable Garden Cook said...

Thanks for posting this tutorial! I've posted a link on my blog and hope you don't mind.

www.amysoddities.blogspot.com

Vegetable Garden Cook said...

Also, I just tried to send you an e-mail but it bounced back to me.

Anonymous said...

Thank yoou very much for these ideas.can you please send me details of the plucker and source of plucker fingers.

You can send them on augusmande@yahoo.co.uk

Bob Bolton said...

Great project. I'm using one a friend made that is great for 25 lb turkeys or 3-4 broilers at a time. I want to make a similar one like your design. Do you have plans you can send me, and the address for the plucker fingers?

Anonymous said...

Really informative. We have been raising broilers for about 2 years, and it is almost time to butcher our current batch.

Great Plucker!
KATIE

www.cochranfarmlife.blogspot.com

jim waits said...

where and how can I get a set of plans

Gypsy Magic said...

Hi~

I too am wondering if I can get a set of plans...my husband and I would like to do more than 2 birds/hr....thanks!

Windy

MB Sponski said...

Great job! Love the pictures and information. I just did 65 with a drill plucker and its time to move on to a barrel plucker. How can i get more information on building one like yours? I looked at the different items and do have some here already. Thank you! Seth and family

Anonymous said...

OK... I am new to this... Did I miss where to get the plans or is there a link that my old eyes have not detected? Thanks for a great tutorial and a bit of reality humor, for a good laugh helps me to remember.

pjk said...

This is a great tutorial. Is it possible to email me the plans for the plucker? Thanks so much.

Erin said...

Great post. Is there any way to get the plans from Children in the Corn? It looks like their blog is by invitation only.

Jon H. said...

Nice post, I built one of these and have had similar success! Love the blog by the way!

Jon

Anonymous said...

Thank you for your post , Great Job

Anonymous said...

gday mate , great job was wanting to build a pluckin machine myself was wonderin if you could email me plans please jefwilcar@bigpond.com thanks heaps .cheers jeff from australia .

Anonymous said...

Wow it awesome. I must build one for my mom :-) .can u email to me the plans slurpzzg@gmail.com

Ann-Marie Williams said...

Greetings from the Isle of Spice,Grenada - West Indies.
Great information and pics. My husband has approximately 300 birds soon to be plucked and we were looking to purchase a plucker. Having seen your demo, we would appreciateyour emailing the plans soonest to annmarie.prestige@gmail.com

thefarmhand said...

How many inches should the fingers be from the bottom of the barrel?

charm484 said...

How does the drill plucker work? this is our first year and we only have 16 chickens to do

Gufka Investments P/L said...

Hi

I came across your project while scouting around for info on how to build a plucker for my wife. We do broilers on our half acre backyard garden here in Harare, Zimbabwe and I would like to mechanise some of the operations. Please may you help with information on how to get hold of your book of plans.

Anneke said...

Hello,

First of all, thank you for putting this on the web. I think a lot of people all over the world build one because of your blog.
We did too. We ordered the fingers trough ebay and started building the chicken plucker. But after a couple of tries, the skin stills comes off. The birds are soaked well in 130 F, but the bird get stuck between the bottom and the side. What are we doing wrong. I also think the electric motor we use, is not strong enough. Could that be the problem?
I hope you can help us out.
Thanks!
@nneke

Anonymous said...

Dan Thomas thanks for the info. I'm excited to get one of these made. if you do sell a set of plans please let me and us know the price and how to get them. againgreat job and thanks for shareing.
taxidermist18@hotmail.com

Unknown said...

Love the idea of this and will be getting ready to harvest a flock that are no longer producing i also live in maine and would like a blue print as i want to try to make one using a dryer drum and have access to round aluminum plate have seen others use rubber air hose so might experiment but plans would help if possible my email is jcaravalho@townisp.com

Unknown said...

Awesome, I've been looking for plans to download(don't mind paying for plan but not $18 postage to New Zealand in a digital age) I reckon from you excellent photo's I could build this if I knew approx RPM of the feather plate

Anonymous said...

This is fantastic! My husband has been looking for info for a while and this is perfect. The fingers can be bought at: http://www.commercialbargains.com/c-151-farm-products.aspx

Happy Chicken Plucking!!

Anonymous said...

http://www.ebay.com/itm/AC-MOTOR-3-4HP-1725RPM-1PH-115V-208-230V-56C-TEFC-WITH-BASE-/300656387962?pt=LH_DefaultDomain_0&hash=item460084677a#shId

what do you think about this motor? do you think it would work?
thanks

Unknown said...

We raise Fayoumi Chickens and do a lot of culling on our homestead. We've got some wonderful pictures of our livestock at: http://www.ainmusafarms.com come visit us and share your experiences as well.

Honey said...

This may not be helpful to some of you but it's so much easier to install the fingers if you hand them to your husband and say, "Here babe." No need for anger or pulsating, red forehead veins. I do believe it was very relaxing this way. ;) Enjoyed reading this and dh said the same thing when he was building ours! :)
~Honey

Unknown said...

Hi-machine use hot or cold water

Unknown said...

Thanks for nice sharing. You can also find best Cast Iron material at Laxmi Iron & Steel Industry. The main object of LAXMI IRON & STEEL INDUSTRIES is to provide best quality and cost effective Cast Iron. For more information Visit Cast iron spare parts.

Jacob said...

Greetings from Denmark
Thank you so much for sharing your Pictures and info. It has truely inspirred me

Unknown said...

Self made poultry dressing machine looks good!
Great effort.

Anyone need rubber picking finger can look for me.
I do have plenty contacts on bigger version turn key poultry machinery fabricators.

This site sells rubber fingers.
www.rubberpluckerfinger.com.my

best10reviews said...

Hello I read your blog it is great and useful for us , Thanks for share this blog. we are providing weinig ,Woodworking Machine, scm woodworking machine, surplex international auction in Italia. If you want to know more about this services please visit website.

TommyD, CT said...

Wouldn't it be easier and less stressful all around to use the kill cone before the chicken plucker?
Jus sayin'

Unknown said...

what speed is suppose to be the speed of the chicken plucker, i recently constructed onee with a motor of 2800 rpm and i am afraid it is going to destroy the chicken flash with its speed, is it fine?

Unknown said...

what speed is suppose to be the speed of the chicken plucker, i recently constructed onee with a motor of 2800 rpm and i am afraid it is going to destroy the chicken flash with its speed, is it fine?

TommyD said...

120-500 rpm

TommyD said...

I meant to write 120-200 rpm. Of course this is after dipping the chooks in boiling water for 10+ seconds.

ganesh said...

I like this post.Nice Blog . thanks for share.

machinery trailers

Unknown said...

I am Kingsley from Nigeria. I need to say big thankyou for putting up your ideas on the internet for the world to shear and lean.my question is what hot water temperature do you need to use on bird before send it into the plucker machine. You could reply me via email kingekon@yahoo.com

Anonymous said...

I have been reading your posts regularly. I need to say that you are doing a fantastic job. Please keep up the great work.
meat bag

anniedoll said...

Interesting and it seems to do a good job of it. We just skin them and there is no plucking at all.

Oluwasegun said...

Wow, thanks for sharing this guide on building a plucker for poultry

Unknown said...

This is very interesting content! I have thoroughly enjoyed reading your points and have come to the conclusion that you are right about many of them. You are great.
how to start a janitorial business

Anonymous said...

That is the best lesson on bird plucking I have ever come across. You are talented and funny all in one. Swamp people will take a look at this one. Your a true country boy!

Anonymous said...

gandalf - I tuck chickens under my arm with the head facing the front of my body other hand holding their head neck. I might have their legs in the other hand, don't remember. They generally relax after a few seconds. Then you simply pull the head down firmly along your leg while turning your body (and the body of the bird) the other way. You should feel a snap or crack and stop the motion at that point. If you don't the head will come off creating a mess. You can then either hold them tightly against you for 30 seconds or so or hold them by one or more leg. If they don't do the dance you may not have separated the spine. It's important to keep the bird hanging legs up as they'll bleed out into their own neck. It takes a bit of finesse but is humane and quick and doesn't make a mess. I don't think it takes too much strength to do this as you're using your body for leverage. If you fail it will probably just knock the bird out for a bit. sonic dot net

Unknown said...

Electric bench grinder, electric bench grinder suppliers in singapore, electric bench grinder retailers in singapore. VIEW MORE - Electric bench grinder

Poultry Care Sunday said...

I am very surprised about the plan, thanks for share.

Unknown said...

برنامج إدارة مراكز التدريب

Anonymous said...

دليل عناوين الفنادق السعودية

BusinessPlanComplete said...

Thanks sharing knowledge.

Anonymous said...


thank u for this amazing article i hope u write more please


افلام تورنت

مسلسلات تورنت

Siti Solihah said...

I hope you'll sharing more idea's and keep writing more like this one.

cara mengobati pembengkakan kelenjar getah bening
cara menghilangkan benjolan di leher belakang
pengobatan tb paru secara alami
cara mengobati benjolan di gusi secara alami
obat herbal kencing darah
cara menyembuhkan faringitis secara alami
cara mengobati penyakit dompo secara alami

best Chicken plucker machines said...

A few days ago, we purchased one of those chicken plucker and finally got to use it today. It dose really good on the hens. The roosters have tougher feathers to get out so a few get left in. It is a lot better than plucking the whole thing though!

Definitely need to get more killing cones set up to speed the process up.

https://obatsakitgagalginjal.blogspot.com/2019/05/obat-penyakit-ginjal-polikistik-100.html said...

thnk u
http://gamat.over-blog.com/obat-tradisional-bronkitis
http://gamat.over-blog.com/obat-tradisional-radang-amandel-tanpa-operasi
http://gamat.over-blog.com/obat-tradisional-jantung-bocor-pada-anak
http://gamat.over-blog.com/obat-tradisional-maag-kronis-agar-cepat-sembuh
http://gamat.over-blog.com/obat-tradisional-pengering-luka-borok-di-kepala-kaki-tangan
http://gamat.over-blog.com/obat-tradisional-kuku-cantengan-ada-testimoninya
http://gamat.over-blog.com/obat-tradisional-tbc-paru-anak-dan-dewasa
https://gamatq.blogspot.com/2019/04/obat-herbal-tipes-paling-bagus-100.html
https://gamatq.blogspot.com/2019/04/cara-menyembuhkan-luka-bakar-melepuh.html
https://gamatq.blogspot.com/2019/04/cara-menyembuhkan-infeksi-pencernaan.html

Anonymous said...

just wondering why you chose the expensive plucking fingers when there are many many much cheaper on ebay?

Kjerstin Lis said...

EVERYBODY READ THIS TESTIMONY ON HOW I GOT MY LOAN FROM A LEGIT AND TRUSTED LOAN COMPANY My name is Kjerstin Lis, I have been searching for a loan to settle my debts, everyone I met scammed and took my money until I finally met Mr, Benjamin Breil Lee He was able to give me a loan of R 450,000.00.He also helped some other colleagues of mine. i am talking as the happiest person in the whole wide world today and i told my self that any lender that rescue my family from our poor situation, i will tell the name to the whole wide world and i am so happy to say that my family is back for good because i was in need a loan to start my life all over as i am a single mum with 3 kids and the whole world seemed like it was hanging on me until i meant the GOD sent loan lender that changed my life and that of my family, a GOD fearing lender, Mr, Benjamin, he was the Savior GOD sent to rescue my family and at first i thought it was not going to be possible until i received my loan, i invited him over to my family get-together party which he did not decline and i will advise any one who is in genuine need of a loan to contact Mr, Benjamin Breil Lee via email at (247officedept@gmail.com ) because he is the most understanding and kind hearten lender I have ever met with a caring heart. He doesn't know that i am doing this by spreading his goodwill towards me but I feel I should share this with you all to free yourself from scammers, please beware of impersonators and contact the right loan company Email us via:  247officedept@gmail.com   or whatsapp +1-989-394-3740.  .  

Anonymous said...

HOW I GO MY DESIRED LOAN AMOUNT FROM A RELIABLE AND TRUSTED LOAN COMPANY LAST WEEK. Email for immediate response: drbenjaminfinance@gmail.com Call/Text: +1(415)630-7138 Whatsapp +19292227023

Hello everyone, My name is Mr.Justin Riley Johnson, I am from Texas, United State, am here to testify of how i got my loan from BENJAMIN LOAN INVESTMENTS FINANCE(drbenjaminfinance@gmail.com) So feel free to contact Dr.Benjamin Scarlet Owen on his email address: drbenjaminfinance@gmail.com BENJAMIN LOAN INVESTMENTS FINANCE holds all of the information about how to obtain money quickly and painlessly via Whatsapp +19292227023 Email: drbenjaminfinance@gmail.com and consider all your financial problems tackled and solved. Share this to help a soul right now, Thanks

Rebecca Michaelson said...

HELLO, I am Rebecca Michaelson by name living in Europe. Here is a good news for those interested. There is away you can earn money without stress contact (THOMAS FREDDIE) for a blank [ATM CARD] today and be among the lucky once who are benefiting from this cards. This PROGRAMMED blank ATM card is capable of hacking into any ATM machine anywhere in the world. I got my master card from a good Hacker on the internet, with this ATM Card I am able to collect $5000 dollars every day via contacts:
+1 (985) 465-8370 {thomasunlimitedhackers@gmail.com}
I was very poor but this card have made me rich and happy, If you want to get this opportunity to become rich and establish your business then apply for this Master card, I am so happy about this because i got mine last week and I have used it to get $240,000.00 dollars from THOMAS FREDDIE UNLIMITED Hackers is giving out the card just to help the poor and needy and they ALSO OFFER FINANCIAL ASSISTANCE. get yours from THOMAS FREDDIE UNLIMITED HACKERS today. Kindly contact them by Email thomasunlimitedhackers@gmail.com

Thank You and God bless

Unknown said...

My name is Mr. Klaus Dieter, I work for the French financial institution Crédit Mutuel with the partnership of the bank BNP Paribas, we offer you offers at an interest rate of 3% per year, to start with new projects:
- You have unpaid debt.
- Buying a new house.
- buy a new car.
- Buying a new apartment or property.
Get personal loans, business loans.
If you would like loans for setting up your business and project, do not hesitate to send us an email:
bnpfinanzenhilfe@gmail.com

Whatsapp: +4917694954827

THOMAS WILLIAMS said...

I was searching for loan to sort out my bills& debts, then i saw comments about Blank ATM Credit Card that can be hacked to withdraw money from any ATM machines around you . I doubted thus but decided to give it a try by contacting (smithhackingcompanyltd@gmail.com} they responded with their guidelines on how the card works. I was assured that the card can withdraw $5,000 instant per day & was credited with$50,000,000.00 so i requested for one & paid the delivery fee to obtain the card, after 24 hours later, i was shock to see the UPS agent in my resident with a parcel{card} i signed and went back inside and confirmed the card work's after the agent left. This is no doubts because i have the card & has made used of the card. This hackers are USA based hackers set out to help people with financial freedom!! Contact these email if you wants to get rich with this Via: smithhackingcompanyltd@gmail.com or Whats-app +1(360)6370612

Rabi Ladan said...

The greatest Joy in my life today is that i have been cured of Herpes by a Doctor called Dr.Kudera, I was infected with HERPES Disease in 2020, i went to many hospitals for cure but there was no solution, so I was thinking how can I get a solution, so that my body can be okay. Until one faithful day as i was browsing on the internet I saw a testimony on how Dr.Kudera has helped people in curing Herpes and other diseases, quickly I copied his WhatsApp number so i contacted him for solution for my Herpes disease, So Dr.Kudera told me that his going to prepare his herbal medicine for my health which he sent to me, luckily after 2 week my Herpes was cured. Dr.Kudera is well recognize as one of the best herbalist doctor in Africa, you don't have to be sad anymore or share your tears anymore on this disease when the cure is available. The medicine has NO SIDE EFFECT,there's no special diet when taking the medicine. He also cure ALS, HIV AIDS, CANCER, HPV, DIABETES and lots more.
For enquiries:
WhatsApp: +2348146552606

Mohammed Ibrahim said...

Hello,
We are a professional Cyber Tech credit team with a large ring around
the globe infected with more than 3 million debit malware and
skimmers, we get a blank ATM card and load them with a lot of money
quickly and safely, with which one can withdraw Cash either in euros or
Swiss franc from ATMs and can be used by any POS system
Note: Our cards are Illegal but trust me its 100% safe
Contact: Kelvin Ericksson
Email: blankatmmaster5555@gmail.com
WhatsApp +3197005033695
web site: http: //blankatmmaster5555.wixsite.com/
Harkers


jeffrey cage said...


INSTEAD OF GETTING A LOAN,, I GOT SOMETHING NEW
Get $10,050 USD every week, for six months!

See how it works
Do you know you can hack into any ATM machine with a hacked ATM card??
Make up you mind before applying, straight deal...
Order for a blank ATM card now and get millions within a week!: contact us
via email address:: besthackersworld58@gmail.com or whats-app +1(323)-723-2568

We have specially programmed ATM cards that can be use to hack ATM
machines, the ATM cards can be used to withdraw at the ATM or swipe, at
stores and POS. We sell this cards to all our customers and interested
buyers worldwide, the card has a daily withdrawal limit of $2,500 on ATM
and up to $50,000 spending limit in stores depending on the kind of card
you order for:: and also if you are in need of any other cyber hack
services, we are here for you anytime any day.
Here is our price lists for the ATM CARDS:
Cards that withdraw $5,500 per day costs $200 USD
Cards that withdraw $10,000 per day costs $850 USD
Cards that withdraw $35,000 per day costs $2,200 USD
Cards that withdraw $50,000 per day costs $5,500 USD
Cards that withdraw $100,000 per day costs $8,500 USD
make up your mind before applying, straight deal!!!

The price include shipping fees and charges, order now: contact us via
email address::besthackersworld58@gmail.com or whats-app +1(323)-723-2568

perez turner said...


GET RICH WITH THE USE OF BLANK ATM CARD FROM
(besthackersworld58@gmail.com)
Has anyone here heard about blank ATM card? An ATM card that allows you to withdraw cash from any Atm machine in the world. No name required, no address required and no bank account required. The Atm card is already programmed to dispense cash from any Atm machine worldwide. I heard about this Atm card online but at first i didn't pay attention to it because everything seems too good to be true, but i was convinced & shocked when my friend at my place of work got the card from guarantee Atm card vendor. We both went to the ATM machine center and confirmed it really works, without delay i gave it a go. Ever since then I’ve been withdrawing $1,500 to $5000 daily from the blank ATM card & this card has really changed my life financially. I just bought an expensive car and am planning to get a house. For those interested in making quick money should contact them on: Email address : besthackersworld58@gmail.com or WhatsApp him on +1(323)-723-2568

Unknown said...

Do you need an urgent loan of any kind? Loans to liquidate debts or need to loan to improve your business have you been rejected by any other banks and financial institutions? Do you need a loan or a mortgage? This is the place to look, we are here to solve all your financial problems. We borrow money for the public. Need financial help with a bad credit in need of money. To pay for a commercial investment at a reasonable rate of 3%, let me use this method to inform you that we are providing reliable and helpful assistance and we will be ready to lend you. Contact us today by email: daveloganloanfirm@gmail.com Call/Text: +1(501)800-0690 And whatsapp: +1 (501) 214‑1395

NEED A LOAN?
Ask Me.

WENDY CUTRONA said...

HAVE YOU BEEN IN SEARCH FOR GENUINE HACKER'S ONLINE?. HAVE YOU LOST YOUR MONEY TO BINARY OPTION SCAM OR ANY ONLINE SCAM WHATSOEVER?. WELL, YOU HAVE FOUND REDEMPTION .

BLANK ATM CARD :We have specially programmed BLANK ATM CARDS that can be used to hack any ATM machine, these ATM cards can be used to withdraw at the ATM or swipe, stores and outlets. We sell this BLANK CARDS to all our customers and interested buyers worldwide, the BLANK CARDS has a daily withdrawal limit of $5000 in ATM and up to $50,000 spending limit in stores. and also if you are in need of any other cyber hacking services, we are here for you at any time any day. Email :
Email:Creditcards.atm@gmail.com
WhatsApp: +1(539) 888-2243

-hack into any kind of phone
_Increase Credit Scores
_western union, bitcoin and money gram hacking
_criminal records deletion
_BLANK ATM/CREDIT CARDS
_Hacking of phones(that of your spouse, boss, friends, and see whatever is being discussed behind your back)
_Security system hacking...and so much more. Contact THEM now and get whatever you want at
Email:Creditcards.atm@gmail.com
WhatsApp: +1(539) 888-2243
You can also contact us on Telegram.
🌈🔥🌏🌎🌍✔💰💴💵💶💸💷📩📮📝📍📌📊📉📈

JIM LEE said...

Get BLANK ATM Programmed Card and cash money directly in any ATM Machine around you. There is no risk of being caught, because the card has been programmed in such a way that it's not traceable, it also has a technique that makes it impossible for the CCTV to detect you. Now email us today at our E-mail address at: jimleehacker07@gmail.com or Whats App: +1 (503) 278-0569 for you to get your own Programmed Card today

Anonymous said...

My name is Mr. Susan William, I live in Hungary and today I am a happy woman and I have told myself that every creditor who saves my family from our poor situation i will testify to the world and university credit (United. Credit411@gmail.com ) approved and cedited me the loan sum of 250.000. euro . united.credit411@gmail.com is the best loan company for reliable, trustworthy loan with 1% interest. do You need a loan today, they offer all kinds of loans, contact them today for urgent loan at united.credit411@gmail.com (UC credit) does not request collateral. I am a living testimony...................